{"id":169,"date":"2026-11-05T21:05:00","date_gmt":"2026-11-06T02:05:00","guid":{"rendered":"https:\/\/signalsandstatic.com\/?p=169"},"modified":"2026-11-11T22:25:32","modified_gmt":"2026-11-12T03:25:32","slug":"two-node-openmanet-mesh-push-to-talk","status":"publish","type":"post","link":"https:\/\/signalsandstatic.com\/?p=169","title":{"rendered":"Two-Node OpenMANET Mesh Is Up (and Push-to-Talk Works)"},"content":{"rendered":"<p>The Seeed box showed up, the radios went on the HATs, and I now have a working two-node <strong>OpenMANET mesh<\/strong> on the bench with push-to-talk voice crossing the HaLow link. If you&#8217;re following along, this is where the <a href=\"https:\/\/signalsandstatic.com\/?p=168\">phase 1 parts<\/a> turn into an actual network. Notes below, including the dumb mistake.<\/p>\n<h2>Bringing up the OpenMANET mesh<\/h2>\n<p>Both nodes run OpenMANET 1.8.0. The setup wizard walks you through the HaLow settings, and you decide each node&#8217;s job:<\/p>\n<ul>\n<li><strong>Node 1: mesh gate<\/strong> (router mode). It lands at <code>10.41.0.1<\/code> and is the node that would NAT the mesh onto an uplink.<\/li>\n<li><strong>Node 2: bridge mode.<\/strong> A plain mesh node with its own access point and Ethernet.<\/li>\n<\/ul>\n<p>The mesh settings have to match exactly on both nodes: mesh ID, channel, bandwidth and passphrase. If they don&#8217;t, nothing finds anything.<\/p>\n<h3>The ten-minute mistake<\/h3>\n<p>Node 2 came up, and its dashboard said <strong>0 connected mesh nodes<\/strong>. I checked antennas. I re-read the wizard summary. I started comparing wireless settings.<\/p>\n<p>Node 1 was turned off.<\/p>\n<p>Powered it back on, waited two or three minutes, refreshed, and the counter went to 1. In my defense, there&#8217;s a real thing that makes this confusing: on a fresh install a node starts on a temporary address, picks a permanent one after about two minutes, and reboots. Sometimes the mesh link only comes up after that reboot. So give it a few minutes before you start troubleshooting. And make sure the other node is on.<\/p>\n<h3>How I knew it was really working<\/h3>\n<p>Laptop plugged into node 2&#8217;s Ethernet, browser pointed at <code>http:\/\/10.41.0.1<\/code>, node 1&#8217;s dashboard loads. Node 1&#8217;s own access point showed zero clients, so that page had to come across the radio: laptop \u2192 node 2 \u2192 HaLow \u2192 node 1. That&#8217;s the moment it stops being a pile of boards and becomes a network.<\/p>\n<h2>First link numbers<\/h2>\n<p>With the nodes a few feet apart, this is the bench baseline I&#8217;ll compare against once we go out for range testing:<\/p>\n<table>\n<thead>\n<tr>\n<th>Measurement<\/th>\n<th>Value<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Signal<\/td>\n<td>\u221236 dBm<\/td>\n<\/tr>\n<tr>\n<td>Noise floor<\/td>\n<td>\u221287 dBm<\/td>\n<\/tr>\n<tr>\n<td>Margin<\/td>\n<td>about 51 dB<\/td>\n<\/tr>\n<tr>\n<td>Rate<\/td>\n<td>MCS 7 at 2 MHz (top rate for that width)<\/td>\n<\/tr>\n<tr>\n<td>Throughput shown<\/td>\n<td>7.5 Mbps<\/td>\n<\/tr>\n<tr>\n<td>Encryption<\/td>\n<td>WPA3-SAE<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<div id=\"attachment_181\" style=\"width: 594px\" class=\"wp-caption aligncenter\"><a href=\"https:\/\/signalsandstatic.com\/wp-content\/uploads\/2026\/11\/openmanet-halow-link-margin-bench-test-1.png\"><img loading=\"lazy\" decoding=\"async\" aria-describedby=\"caption-attachment-181\" class=\"size-large wp-image-181\" src=\"https:\/\/signalsandstatic.com\/wp-content\/uploads\/2026\/11\/openmanet-halow-link-margin-bench-test-1.png\" alt=\"OpenMANET mesh bench test: -36 dBm signal against a -87 dBm noise floor for about 51 dB of margin, MCS 7 at 2 MHz, 7.5 Mbps, WPA3-SAE\" width=\"584\" height=\"311\" srcset=\"https:\/\/signalsandstatic.com\/wp-content\/uploads\/2026\/11\/openmanet-halow-link-margin-bench-test-1.png 1200w, https:\/\/signalsandstatic.com\/wp-content\/uploads\/2026\/11\/openmanet-halow-link-margin-bench-test-1-300x160.png 300w, https:\/\/signalsandstatic.com\/wp-content\/uploads\/2026\/11\/openmanet-halow-link-margin-bench-test-1-1024x546.png 1024w, https:\/\/signalsandstatic.com\/wp-content\/uploads\/2026\/11\/openmanet-halow-link-margin-bench-test-1-768x410.png 768w, https:\/\/signalsandstatic.com\/wp-content\/uploads\/2026\/11\/openmanet-halow-link-margin-bench-test-1-500x267.png 500w\" sizes=\"auto, (max-width: 584px) 100vw, 584px\" \/><\/a><p id=\"caption-attachment-181\" class=\"wp-caption-text\">Bench baseline with the nodes a few feet apart: about 51 dB of margin.<\/p><\/div>\n<p>Fifty-one dB of margin at arm&#8217;s length is exactly what you&#8217;d expect. The interesting number will be how fast that shrinks across the property.<\/p>\n<h2>Housekeeping before anything else<\/h2>\n<ol>\n<li><strong>Hostnames.<\/strong> I named them <code>manet01<\/code> and <code>manet02<\/code>. Node addresses move around while auto-addressing settles, so use <code>manet02.local<\/code> instead of chasing IPs.<\/li>\n<li><strong>Root passwords<\/strong> on both nodes: System \u2192 Administration. Different from the mesh and Wi-Fi passphrases.<\/li>\n<li><strong>Replace the default mesh passphrase.<\/strong> This one has an order to it, because the moment one node changes its key it drops off the mesh.<\/li>\n<\/ol>\n<h3>Swapping the mesh passphrase without locking yourself out<\/h3>\n<p>Change the node you&#8217;re plugged into first, then reach the other node over its own Wi-Fi and change it. You&#8217;re always directly connected to the node you&#8217;re editing, so neither drops you mid-save.<\/p>\n<ol>\n<li>Turn on <strong>Advanced Config<\/strong>, go to <strong>Network \u2192 Wireless<\/strong>, and edit the HaLow <strong>Mesh Point<\/strong> entry (not the access point entry).<\/li>\n<li>On the <strong>Wireless Security<\/strong> tab, replace the key, then <strong>Save<\/strong> and <strong>Save &amp; Apply<\/strong>. That node drops off the mesh, which is expected.<\/li>\n<li>Join the other node&#8217;s access point, browse to it, and repeat with the exact same passphrase.<\/li>\n<li>Wait a minute and check that the dashboard shows 1 connected mesh node again.<\/li>\n<\/ol>\n<p>If LuCI warns it&#8217;s about to roll back because it lost contact, choose &#8220;Apply unchecked.&#8221; With this order you shouldn&#8217;t see it.<\/p>\n<h2>Push-to-talk across the OpenMANET mesh<\/h2>\n<p>This is the part I actually wanted. OpenMANET&#8217;s comms run Opus voice over multicast, organized into talk groups, and a phone&#8217;s web browser can act as the radio&#8217;s audio. No app to install.<\/p>\n<p>The important bit: <strong>each device has to be on a different node<\/strong>, otherwise you&#8217;re just testing Wi-Fi in one box. My setup was the phone on node 1&#8217;s access point and the desktop on node 2&#8217;s Ethernet, so the audio has to ride HaLow.<\/p>\n<ol>\n<li>On each node, open the OpenMANET web app on port 8080 (separate from the LuCI pages), go to <strong>Settings \u2192 General<\/strong>, set <strong>Comms Radio<\/strong> to Enabled and <strong>Control Source<\/strong> to Web UI, and save. This is per node; it doesn&#8217;t carry over.<\/li>\n<li>On each device, open the <strong>HTTPS<\/strong> version on port <strong>8081<\/strong> and accept the self-signed certificate. Browsers only allow microphone access over HTTPS.<\/li>\n<li>Open the <strong>Comms<\/strong> page, allow the mic, and make sure both devices have RX and TX on for the same channel.<\/li>\n<li>Hold the big PTT button on one and talk.<\/li>\n<\/ol>\n<div id=\"attachment_183\" style=\"width: 594px\" class=\"wp-caption aligncenter\"><a href=\"https:\/\/signalsandstatic.com\/wp-content\/uploads\/2026\/11\/openmanet-push-to-talk-test-path-1.png\"><img loading=\"lazy\" decoding=\"async\" aria-describedby=\"caption-attachment-183\" class=\"size-large wp-image-183\" src=\"https:\/\/signalsandstatic.com\/wp-content\/uploads\/2026\/11\/openmanet-push-to-talk-test-path-1.png\" alt=\"OpenMANET mesh push-to-talk test: phone on node 1's Wi-Fi, desktop on node 2's Ethernet, audio crossing the 915 MHz HaLow link\" width=\"584\" height=\"273\" srcset=\"https:\/\/signalsandstatic.com\/wp-content\/uploads\/2026\/11\/openmanet-push-to-talk-test-path-1.png 1200w, https:\/\/signalsandstatic.com\/wp-content\/uploads\/2026\/11\/openmanet-push-to-talk-test-path-1-300x140.png 300w, https:\/\/signalsandstatic.com\/wp-content\/uploads\/2026\/11\/openmanet-push-to-talk-test-path-1-1024x478.png 1024w, https:\/\/signalsandstatic.com\/wp-content\/uploads\/2026\/11\/openmanet-push-to-talk-test-path-1-768x358.png 768w, https:\/\/signalsandstatic.com\/wp-content\/uploads\/2026\/11\/openmanet-push-to-talk-test-path-1-500x233.png 500w\" sizes=\"auto, (max-width: 584px) 100vw, 584px\" \/><\/a><p id=\"caption-attachment-183\" class=\"wp-caption-text\">Each device on a different node, so the voice has to cross the HaLow link.<\/p><\/div>\n<p>It works. Voice out of the desktop, keyed from the phone, across the mesh.<\/p>\n<h3>Gotchas I hit<\/h3>\n<ul>\n<li><strong>Make sure the device is actually on the mesh.<\/strong> My desktop first reached node 1 through my home network (a <code>192.168.x.x<\/code> address) instead of the mesh. You need a <code>10.41.x.x<\/code> address. Run <code>ipconfig<\/code> and check.<\/li>\n<li><strong>If the mic meter doesn&#8217;t move<\/strong> when you talk, that browser doesn&#8217;t have mic access. Usually it&#8217;s because you&#8217;re on port 8080 instead of 8081.<\/li>\n<li><strong>Separate the devices<\/strong>, or use earbuds on one, or you&#8217;ll get feedback squeal.<\/li>\n<li>While you&#8217;re in there, the Comms page has offline speech-to-text, and there&#8217;s a Topology page that draws the mesh.<\/li>\n<\/ul>\n<h2>What&#8217;s next<\/h2>\n<ul>\n<li><strong>A real channel knob.<\/strong> The five channels on the Comms page are talk groups, each with its own send\/receive switch, and openmanetd lets other programs flip them through its API. I want a detented rotary switch (a binary-coded one only needs 3\u20134 wires) wired straight to the Pi&#8217;s GPIO, with a small service that turns &#8220;position 3&#8221; into &#8220;talk and listen on channel 3.&#8221; The catch is the WM1302 HAT covers the 40-pin header, so that means a stacking header and checking which pins are free. Long term, the knob, PTT and audio go on the CM4 carrier as the radio&#8217;s front panel.<\/li>\n<li><strong>ATAK.<\/strong> The data side clearly works, so position sharing and map markers are next.<\/li>\n<li><strong>Batteries and a range walk<\/strong>, then the 5 GHz dual-band experiment.<\/li>\n<\/ul>\n<p>Two nodes on a bench isn&#8217;t a tactical radio yet. But it&#8217;s a real mesh, it carries voice, and every node I build from here has to keep doing exactly this.<\/p>\n<div style=\"border:1px solid #ddd;border-left:4px solid #e8a33d;background:#fafafa;padding:12px 16px;margin:24px 0;\">\n<p style=\"margin:0 0 6px;\"><strong>The OpenMANET build log<\/strong><\/p>\n<ol style=\"margin:0 0 0 1.4em;\">\n<li><a href=\"https:\/\/signalsandstatic.com\/?p=166\">Part 1: What OpenMANET is (and why I&#8217;m building one)<\/a><\/li>\n<li><a href=\"https:\/\/signalsandstatic.com\/?p=167\">Part 2: The dual-band, CM4 and handheld plan<\/a><\/li>\n<li><a href=\"https:\/\/signalsandstatic.com\/?p=168\">Part 3: Phase 1 parts list<\/a><\/li>\n<li><strong>Part 4: Two-node mesh up, push-to-talk working<\/strong> (you are here)<\/li>\n<li><a href=\"https:\/\/signalsandstatic.com\/?p=199\">Part 5: The handheld, rendered<\/a><\/li>\n<li><a href=\"https:\/\/signalsandstatic.com\/?p=210\">Part 6: A printable Pi 4 test stand<\/a><\/li>\n<li><a href=\"https:\/\/signalsandstatic.com\/?p=223\">Part 7: 5 GHz on the mesh<\/a><\/li>\n<\/ol>\n<\/div>\n<h3>References<\/h3>\n<ul>\n<li><a href=\"https:\/\/openmanet.github.io\/docs\/comms\/how-it-works\" target=\"_blank\" rel=\"noopener\">How OpenMANET comms works<\/a><\/li>\n<li><a href=\"https:\/\/openmanet.github.io\/docs\/\" target=\"_blank\" rel=\"noopener\">OpenMANET documentation<\/a><\/li>\n<\/ul>\n<p>\u2014<br \/><strong>TL;DR:<\/strong> Two Pi 4 nodes, one HaLow mesh at \u221236 dBm with a 51 dB margin, WPA3 encrypted, and browser push-to-talk working across it. Give new nodes a few minutes to settle, change the mesh passphrase in the right order, and make sure both nodes are actually turned on.<\/p>\n","protected":false},"excerpt":{"rendered":"<p>Radios in, two Raspberry Pi 4 nodes meshed over 915 MHz HaLow, and push-to-talk voice crossing the link. Bring-up notes, the link numbers, the passphrase swap that won&#8217;t lock you out, and the one mistake that cost me ten minutes. <a href=\"https:\/\/signalsandstatic.com\/?p=169\">Continue reading <span class=\"meta-nav\">&rarr;<\/span><\/a><\/p>\n","protected":false},"author":1,"featured_media":182,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[12],"tags":[19,3,17,16,13,28,25,18,14],"class_list":["post-169","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-openmanet-build","tag-batman-adv","tag-how-to","tag-manet","tag-mesh-networking","tag-openmanet","tag-openwrt","tag-push-to-talk","tag-raspberry-pi","tag-wi-fi-halow"],"yoast_head":"<!-- This site is optimized with the Yoast SEO plugin v28.8 - https:\/\/yoast.com\/product\/yoast-seo-wordpress\/ -->\n<title>Two-Node OpenMANET Mesh Is Up (and Push-to-Talk Works) | Signals &amp; Static<\/title>\n<meta name=\"description\" content=\"My two-node OpenMANET mesh is up on Raspberry Pi 4s and HaLow, and push-to-talk works across it. Bring-up steps, link numbers, gotchas and what&#039;s next.\" \/>\n<meta name=\"robots\" content=\"index, follow, max-snippet:-1, max-image-preview:large, max-video-preview:-1\" \/>\n<link rel=\"canonical\" href=\"https:\/\/signalsandstatic.com\/?p=169\" \/>\n<meta property=\"og:locale\" content=\"en_US\" \/>\n<meta property=\"og:type\" content=\"article\" \/>\n<meta property=\"og:title\" content=\"Two-Node OpenMANET Mesh Is Up (and Push-to-Talk Works) | Signals &amp; Static\" \/>\n<meta property=\"og:description\" content=\"My two-node OpenMANET mesh is up on Raspberry Pi 4s and HaLow, and push-to-talk works across it. Bring-up steps, link numbers, gotchas and what&#039;s next.\" \/>\n<meta property=\"og:url\" content=\"https:\/\/signalsandstatic.com\/?p=169\" \/>\n<meta property=\"og:site_name\" content=\"Signals &amp; Static\" \/>\n<meta property=\"article:published_time\" content=\"2026-11-06T02:05:00+00:00\" \/>\n<meta property=\"article:modified_time\" content=\"2026-11-12T03:25:32+00:00\" \/>\n<meta property=\"og:image\" content=\"https:\/\/signalsandstatic.com\/wp-content\/uploads\/2026\/11\/openmanet-two-node-mesh-ptt-hero-1.png\" \/>\n\t<meta property=\"og:image:width\" content=\"1200\" \/>\n\t<meta property=\"og:image:height\" content=\"630\" \/>\n\t<meta property=\"og:image:type\" content=\"image\/png\" \/>\n<meta name=\"author\" content=\"admin\" \/>\n<meta name=\"twitter:card\" content=\"summary_large_image\" \/>\n<meta name=\"twitter:label1\" content=\"Written by\" \/>\n\t<meta name=\"twitter:data1\" content=\"admin\" \/>\n\t<meta name=\"twitter:label2\" content=\"Est. reading time\" \/>\n\t<meta name=\"twitter:data2\" content=\"6 minutes\" \/>\n<script type=\"application\/ld+json\" class=\"yoast-schema-graph\">{\"@context\":\"https:\\\/\\\/schema.org\",\"@graph\":[{\"@type\":\"Article\",\"@id\":\"https:\\\/\\\/signalsandstatic.com\\\/?p=169#article\",\"isPartOf\":{\"@id\":\"https:\\\/\\\/signalsandstatic.com\\\/?p=169\"},\"author\":{\"name\":\"admin\",\"@id\":\"https:\\\/\\\/signalsandstatic.com\\\/#\\\/schema\\\/person\\\/ed557e6745a0cd8f039093c317e84f5a\"},\"headline\":\"Two-Node OpenMANET Mesh Is Up (and Push-to-Talk Works)\",\"datePublished\":\"2026-11-06T02:05:00+00:00\",\"dateModified\":\"2026-11-12T03:25:32+00:00\",\"mainEntityOfPage\":{\"@id\":\"https:\\\/\\\/signalsandstatic.com\\\/?p=169\"},\"wordCount\":1179,\"commentCount\":2,\"image\":{\"@id\":\"https:\\\/\\\/signalsandstatic.com\\\/?p=169#primaryimage\"},\"thumbnailUrl\":\"https:\\\/\\\/signalsandstatic.com\\\/wp-content\\\/uploads\\\/2026\\\/11\\\/openmanet-two-node-mesh-ptt-hero-1.png\",\"keywords\":[\"batman-adv\",\"How-To\",\"MANET\",\"Mesh Networking\",\"OpenMANET\",\"OpenWrt\",\"Push-to-Talk\",\"Raspberry Pi\",\"Wi-Fi HaLow\"],\"articleSection\":[\"OpenMANET Build\"],\"inLanguage\":\"en-US\",\"potentialAction\":[{\"@type\":\"CommentAction\",\"name\":\"Comment\",\"target\":[\"https:\\\/\\\/signalsandstatic.com\\\/?p=169#respond\"]}]},{\"@type\":\"WebPage\",\"@id\":\"https:\\\/\\\/signalsandstatic.com\\\/?p=169\",\"url\":\"https:\\\/\\\/signalsandstatic.com\\\/?p=169\",\"name\":\"Two-Node OpenMANET Mesh Is Up (and Push-to-Talk Works) | Signals & Static\",\"isPartOf\":{\"@id\":\"https:\\\/\\\/signalsandstatic.com\\\/#website\"},\"primaryImageOfPage\":{\"@id\":\"https:\\\/\\\/signalsandstatic.com\\\/?p=169#primaryimage\"},\"image\":{\"@id\":\"https:\\\/\\\/signalsandstatic.com\\\/?p=169#primaryimage\"},\"thumbnailUrl\":\"https:\\\/\\\/signalsandstatic.com\\\/wp-content\\\/uploads\\\/2026\\\/11\\\/openmanet-two-node-mesh-ptt-hero-1.png\",\"datePublished\":\"2026-11-06T02:05:00+00:00\",\"dateModified\":\"2026-11-12T03:25:32+00:00\",\"author\":{\"@id\":\"https:\\\/\\\/signalsandstatic.com\\\/#\\\/schema\\\/person\\\/ed557e6745a0cd8f039093c317e84f5a\"},\"description\":\"My two-node OpenMANET mesh is up on Raspberry Pi 4s and HaLow, and push-to-talk works across it. Bring-up steps, link numbers, gotchas and what's next.\",\"breadcrumb\":{\"@id\":\"https:\\\/\\\/signalsandstatic.com\\\/?p=169#breadcrumb\"},\"inLanguage\":\"en-US\",\"potentialAction\":[{\"@type\":\"ReadAction\",\"target\":[\"https:\\\/\\\/signalsandstatic.com\\\/?p=169\"]}]},{\"@type\":\"ImageObject\",\"inLanguage\":\"en-US\",\"@id\":\"https:\\\/\\\/signalsandstatic.com\\\/?p=169#primaryimage\",\"url\":\"https:\\\/\\\/signalsandstatic.com\\\/wp-content\\\/uploads\\\/2026\\\/11\\\/openmanet-two-node-mesh-ptt-hero-1.png\",\"contentUrl\":\"https:\\\/\\\/signalsandstatic.com\\\/wp-content\\\/uploads\\\/2026\\\/11\\\/openmanet-two-node-mesh-ptt-hero-1.png\",\"width\":1200,\"height\":630,\"caption\":\"Two-node OpenMANET mesh is up and push-to-talk works: first light on the bench, WPA3 mesh, voice across HaLow\"},{\"@type\":\"BreadcrumbList\",\"@id\":\"https:\\\/\\\/signalsandstatic.com\\\/?p=169#breadcrumb\",\"itemListElement\":[{\"@type\":\"ListItem\",\"position\":1,\"name\":\"Home\",\"item\":\"https:\\\/\\\/signalsandstatic.com\\\/\"},{\"@type\":\"ListItem\",\"position\":2,\"name\":\"Two-Node OpenMANET Mesh Is Up (and Push-to-Talk Works)\"}]},{\"@type\":\"WebSite\",\"@id\":\"https:\\\/\\\/signalsandstatic.com\\\/#website\",\"url\":\"https:\\\/\\\/signalsandstatic.com\\\/\",\"name\":\"Signals &amp; Static\",\"description\":\"Random transmissions, straight from the source\",\"potentialAction\":[{\"@type\":\"SearchAction\",\"target\":{\"@type\":\"EntryPoint\",\"urlTemplate\":\"https:\\\/\\\/signalsandstatic.com\\\/?s={search_term_string}\"},\"query-input\":{\"@type\":\"PropertyValueSpecification\",\"valueRequired\":true,\"valueName\":\"search_term_string\"}}],\"inLanguage\":\"en-US\"},{\"@type\":\"Person\",\"@id\":\"https:\\\/\\\/signalsandstatic.com\\\/#\\\/schema\\\/person\\\/ed557e6745a0cd8f039093c317e84f5a\",\"name\":\"admin\",\"image\":{\"@type\":\"ImageObject\",\"inLanguage\":\"en-US\",\"@id\":\"https:\\\/\\\/secure.gravatar.com\\\/avatar\\\/da83388a664af9173b58164727a96a5dee692bee581ede6eb7036b6f3f31384d?s=96&d=mm&r=g\",\"url\":\"https:\\\/\\\/secure.gravatar.com\\\/avatar\\\/da83388a664af9173b58164727a96a5dee692bee581ede6eb7036b6f3f31384d?s=96&d=mm&r=g\",\"contentUrl\":\"https:\\\/\\\/secure.gravatar.com\\\/avatar\\\/da83388a664af9173b58164727a96a5dee692bee581ede6eb7036b6f3f31384d?s=96&d=mm&r=g\",\"caption\":\"admin\"},\"sameAs\":[\"https:\\\/\\\/signalsandstatic.com\"],\"url\":\"https:\\\/\\\/signalsandstatic.com\\\/?author=1\"}]}<\/script>\n<!-- \/ Yoast SEO plugin. -->","yoast_head_json":{"title":"Two-Node OpenMANET Mesh Is Up (and Push-to-Talk Works) | Signals & Static","description":"My two-node OpenMANET mesh is up on Raspberry Pi 4s and HaLow, and push-to-talk works across it. Bring-up steps, link numbers, gotchas and what's next.","robots":{"index":"index","follow":"follow","max-snippet":"max-snippet:-1","max-image-preview":"max-image-preview:large","max-video-preview":"max-video-preview:-1"},"canonical":"https:\/\/signalsandstatic.com\/?p=169","og_locale":"en_US","og_type":"article","og_title":"Two-Node OpenMANET Mesh Is Up (and Push-to-Talk Works) | Signals & Static","og_description":"My two-node OpenMANET mesh is up on Raspberry Pi 4s and HaLow, and push-to-talk works across it. Bring-up steps, link numbers, gotchas and what's next.","og_url":"https:\/\/signalsandstatic.com\/?p=169","og_site_name":"Signals &amp; Static","article_published_time":"2026-11-06T02:05:00+00:00","article_modified_time":"2026-11-12T03:25:32+00:00","og_image":[{"width":1200,"height":630,"url":"https:\/\/signalsandstatic.com\/wp-content\/uploads\/2026\/11\/openmanet-two-node-mesh-ptt-hero-1.png","type":"image\/png"}],"author":"admin","twitter_card":"summary_large_image","twitter_misc":{"Written by":"admin","Est. reading time":"6 minutes"},"schema":{"@context":"https:\/\/schema.org","@graph":[{"@type":"Article","@id":"https:\/\/signalsandstatic.com\/?p=169#article","isPartOf":{"@id":"https:\/\/signalsandstatic.com\/?p=169"},"author":{"name":"admin","@id":"https:\/\/signalsandstatic.com\/#\/schema\/person\/ed557e6745a0cd8f039093c317e84f5a"},"headline":"Two-Node OpenMANET Mesh Is Up (and Push-to-Talk Works)","datePublished":"2026-11-06T02:05:00+00:00","dateModified":"2026-11-12T03:25:32+00:00","mainEntityOfPage":{"@id":"https:\/\/signalsandstatic.com\/?p=169"},"wordCount":1179,"commentCount":2,"image":{"@id":"https:\/\/signalsandstatic.com\/?p=169#primaryimage"},"thumbnailUrl":"https:\/\/signalsandstatic.com\/wp-content\/uploads\/2026\/11\/openmanet-two-node-mesh-ptt-hero-1.png","keywords":["batman-adv","How-To","MANET","Mesh Networking","OpenMANET","OpenWrt","Push-to-Talk","Raspberry Pi","Wi-Fi HaLow"],"articleSection":["OpenMANET Build"],"inLanguage":"en-US","potentialAction":[{"@type":"CommentAction","name":"Comment","target":["https:\/\/signalsandstatic.com\/?p=169#respond"]}]},{"@type":"WebPage","@id":"https:\/\/signalsandstatic.com\/?p=169","url":"https:\/\/signalsandstatic.com\/?p=169","name":"Two-Node OpenMANET Mesh Is Up (and Push-to-Talk Works) | Signals & Static","isPartOf":{"@id":"https:\/\/signalsandstatic.com\/#website"},"primaryImageOfPage":{"@id":"https:\/\/signalsandstatic.com\/?p=169#primaryimage"},"image":{"@id":"https:\/\/signalsandstatic.com\/?p=169#primaryimage"},"thumbnailUrl":"https:\/\/signalsandstatic.com\/wp-content\/uploads\/2026\/11\/openmanet-two-node-mesh-ptt-hero-1.png","datePublished":"2026-11-06T02:05:00+00:00","dateModified":"2026-11-12T03:25:32+00:00","author":{"@id":"https:\/\/signalsandstatic.com\/#\/schema\/person\/ed557e6745a0cd8f039093c317e84f5a"},"description":"My two-node OpenMANET mesh is up on Raspberry Pi 4s and HaLow, and push-to-talk works across it. Bring-up steps, link numbers, gotchas and what's next.","breadcrumb":{"@id":"https:\/\/signalsandstatic.com\/?p=169#breadcrumb"},"inLanguage":"en-US","potentialAction":[{"@type":"ReadAction","target":["https:\/\/signalsandstatic.com\/?p=169"]}]},{"@type":"ImageObject","inLanguage":"en-US","@id":"https:\/\/signalsandstatic.com\/?p=169#primaryimage","url":"https:\/\/signalsandstatic.com\/wp-content\/uploads\/2026\/11\/openmanet-two-node-mesh-ptt-hero-1.png","contentUrl":"https:\/\/signalsandstatic.com\/wp-content\/uploads\/2026\/11\/openmanet-two-node-mesh-ptt-hero-1.png","width":1200,"height":630,"caption":"Two-node OpenMANET mesh is up and push-to-talk works: first light on the bench, WPA3 mesh, voice across HaLow"},{"@type":"BreadcrumbList","@id":"https:\/\/signalsandstatic.com\/?p=169#breadcrumb","itemListElement":[{"@type":"ListItem","position":1,"name":"Home","item":"https:\/\/signalsandstatic.com\/"},{"@type":"ListItem","position":2,"name":"Two-Node OpenMANET Mesh Is Up (and Push-to-Talk Works)"}]},{"@type":"WebSite","@id":"https:\/\/signalsandstatic.com\/#website","url":"https:\/\/signalsandstatic.com\/","name":"Signals &amp; Static","description":"Random transmissions, straight from the source","potentialAction":[{"@type":"SearchAction","target":{"@type":"EntryPoint","urlTemplate":"https:\/\/signalsandstatic.com\/?s={search_term_string}"},"query-input":{"@type":"PropertyValueSpecification","valueRequired":true,"valueName":"search_term_string"}}],"inLanguage":"en-US"},{"@type":"Person","@id":"https:\/\/signalsandstatic.com\/#\/schema\/person\/ed557e6745a0cd8f039093c317e84f5a","name":"admin","image":{"@type":"ImageObject","inLanguage":"en-US","@id":"https:\/\/secure.gravatar.com\/avatar\/da83388a664af9173b58164727a96a5dee692bee581ede6eb7036b6f3f31384d?s=96&d=mm&r=g","url":"https:\/\/secure.gravatar.com\/avatar\/da83388a664af9173b58164727a96a5dee692bee581ede6eb7036b6f3f31384d?s=96&d=mm&r=g","contentUrl":"https:\/\/secure.gravatar.com\/avatar\/da83388a664af9173b58164727a96a5dee692bee581ede6eb7036b6f3f31384d?s=96&d=mm&r=g","caption":"admin"},"sameAs":["https:\/\/signalsandstatic.com"],"url":"https:\/\/signalsandstatic.com\/?author=1"}]}},"_links":{"self":[{"href":"https:\/\/signalsandstatic.com\/index.php?rest_route=\/wp\/v2\/posts\/169","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/signalsandstatic.com\/index.php?rest_route=\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/signalsandstatic.com\/index.php?rest_route=\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/signalsandstatic.com\/index.php?rest_route=\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/signalsandstatic.com\/index.php?rest_route=%2Fwp%2Fv2%2Fcomments&post=169"}],"version-history":[{"count":6,"href":"https:\/\/signalsandstatic.com\/index.php?rest_route=\/wp\/v2\/posts\/169\/revisions"}],"predecessor-version":[{"id":227,"href":"https:\/\/signalsandstatic.com\/index.php?rest_route=\/wp\/v2\/posts\/169\/revisions\/227"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/signalsandstatic.com\/index.php?rest_route=\/wp\/v2\/media\/182"}],"wp:attachment":[{"href":"https:\/\/signalsandstatic.com\/index.php?rest_route=%2Fwp%2Fv2%2Fmedia&parent=169"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/signalsandstatic.com\/index.php?rest_route=%2Fwp%2Fv2%2Fcategories&post=169"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/signalsandstatic.com\/index.php?rest_route=%2Fwp%2Fv2%2Ftags&post=169"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}