OpenMANET Parts List for Phase 1: Two Raspberry Pi 4 HaLow Nodes

Phase 1 of the build plan is boring on purpose: two stock nodes, built the way the docs say, so I learn how OpenMANET behaves before I start changing things. Here’s the OpenMANET parts list I landed on, what I skipped, and what I’d tell someone else ordering today.

Why Raspberry Pi 4 and not Pi 5

  • Firmware support. The prebuilt OpenMANET images target the Pi 4 and CM4. Not the Pi 5. That settles it.
  • Power. The Pi 4 draws noticeably less than a Pi 5, roughly 3–6 W depending on load. That matters once this runs on batteries.
  • Price. Even after this year’s RAM-driven price hikes, the Pi 4 is still the cheaper board.
  • Path to the CM4. Same chip as the CM4 that the custom carrier board will use, so nothing I learn here gets thrown away.

I already had one Pi 4 from 2020 kicking around and ordered a second 4 GB board.

The radio: Seeed MM6108 vs. Gateworks MM8108

There are two supported HaLow radio paths right now:

Seeed Wio-WM6108 Gateworks GW16167
Chip Morse Micro MM6108 Morse Micro MM8108
Interface SPI, on Seeed’s WM1302 Pi HAT USB, M.2 E-key card
Top PHY rate 32.5 Mbps 43.3 Mbps, plus 1–3 dB better sensitivity
Rough cost per node about $140 all-in about $220 all-in
Bonus Pi’s onboard Wi-Fi still works as the client access point Card moves straight onto a custom carrier’s M.2 slot

For a proof of concept I went with the Seeed Wio-WM6108: cheap, in stock, and the reference build in the docs. The GW16167 ($59 each, plus a flat shipping charge from Gateworks) is the plan for the CM4 alpha board later.

One correction to something I believed early on: the Pi’s onboard Wi-Fi is only unusable on SDIO radio builds. On the Seeed SPI build it works fine as the access point your phone joins.

The Seeed order

Part Qty Each Notes
Wio-WM6108 HaLow card (mini-PCIe) 2 $14.99 MM6108, u.FL antenna port
WM1302 Pi HAT 2 $21.99 Carries the card on the Pi’s 40-pin header
868/915 MHz antenna, 2 dBi, SMA, folding 2 $2.49 The antenna the docs list
u.FL to SMA bulkhead cable, 120 mm 6 $1.99 2 needed, 4 spares
Subtotal $90.88 About 2 weeks to ship

The rest came from the usual places:

  • Second Raspberry Pi 4 (4 GB)
  • Two microSD cards
  • Two quality USB-C power supplies and two 60 W-rated USB-C cables (cheap cables are the #1 cause of Pi brownouts)
  • USB GPS dongles for node position
Block diagram of one OpenMANET parts list node: Raspberry Pi 4 with WM1302 HAT and Wio-WM6108, 915 MHz antenna via u.FL to SMA pigtail, USB-C power, USB GPS, microSD and Ethernet

One phase 1 node, block by block. Build two.

Deferred on purpose: batteries

Phase 1 runs on wall power. The plan for walk-around range testing is Waveshare’s UPS HAT (D) with two 21700 cells per node, which is the UPS the OpenMANET docs test with. None of that blocks bench work, so it waits.

Gotchas while ordering

  • The cable shows up under a different name in the cart. The u.FL to SMA-K cable from the docs is listed as “SMA to I-PEX Antenna Cable.” u.FL and I-PEX 1 are the same connector, so it’s the right part.
  • Know which end is which. The SMA end is a female bulkhead jack with a nut and washer (it’ll go through a case wall later); the folding antenna’s male SMA screws onto it.
  • Don’t put the antenna on the wrong socket. When you assemble, make sure the u.FL clicks onto the radio card’s antenna port and not a GPS socket.

Flash while you wait on radios

The Pis and SD cards showed up before the Seeed box, so I got a head start. The current stable firmware when I flashed was OpenMANET 1.8.0.

  1. From the firmware releases page, download the Pi 4 MM6108 SPI image: openmanet-1.8.0-rpi4-mm6108-spi-squashfs-sysupgrade.img.gz. Skip older pre-releases.
  2. Check the hash. In PowerShell: Get-FileHash .\openmanet-1.8.0-rpi4-mm6108-spi-squashfs-sysupgrade.img.gz, and compare it with the one on the release page.
  3. In Raspberry Pi Imager pick Raspberry Pi 4, “Use custom,” the .img.gz (no need to unzip), then the card. Say No to OS customization.
  4. Boot each Pi on its own brick and cable, plug in Ethernet, and confirm the web UI loads at http://10.41.254.1. That checks the Pi, card, supply and cable in one go.

Then stop. Don’t run the setup wizard until the radios are installed, because the wizard configures the HaLow settings.

Next post: radios in, two nodes talking, and push-to-talk across the mesh.

References

—
TL;DR: Two Pi 4s, two Seeed Wio-WM6108 cards on WM1302 HATs, folding 915 MHz antennas, good USB-C power. The Seeed part of the order was $90.88. Flash 1.8.0 and smoke-test the Pis while you wait, but hold the setup wizard until the radios are in.

4 thoughts on “OpenMANET Parts List for Phase 1: Two Raspberry Pi 4 HaLow Nodes”

  1. Pingback: Two-Node OpenMANET Mesh Is Up (and Push-to-Talk Works) | Signals & StaticSignals & Static

  2. Pingback: OpenMANET Dual-Band Plan: HaLow + 5 GHz, CM4 and a Handheld | Signals & StaticSignals & Static

  3. Pingback: OpenMANET: A Wi-Fi HaLow Mesh Radio Worth Building | Signals & StaticSignals & Static

  4. Pingback: Free STL: Raspberry Pi 4 Test Stand for OpenMANET Nodes | Signals & StaticSignals & Static

Leave a Reply

Your email address will not be published. Required fields are marked *